← Firsthand QC Save as PDF
Firsthand QC
Pre-Shipment Inspection Report
Report no. FHQC-SAMPLE-001
Inspector: Shawn Gao
[email protected]
SAMPLE REPORT: all names, figures and findings below are illustrative, to show the report format. This is not a report of a real inspection, brand or factory.
FAILMajor defects over the acceptance limit
Key findings
  • 9 major defects in 125 samples, against an acceptance limit of 7. Five are coating chips at the base edge.
  • 1 unit lost its vacuum: outer wall at 41 °C after a hot fill (unit #88).
  • Coating adhesion below spec on 1 of 5 tested units (3B against ≥4B), at the same base edge where chips were found.
Recommendation: do not release as is. Factory to sort 100% for base-edge chips and gasket seating, then re-inspect the sorted lot.

1. Order and inspection details

ClientSample Brand Co. (illustrative)
Product500 ml double-wall vacuum bottle, 18/8 stainless steel, powder-coated, screw lid with silicone gasket
Item no. / PO no.SB-500 / SAMPLE-PO-0001
Order quantity3,000 pcs (3 colours × 1,000)
Status at inspection100% produced, 85% packed. 120 export cartons of 25 pcs.
Factory locationYongkang, Zhejiang, China (name withheld in sample)
Inspection typePre-shipment inspection (final random inspection)
Reference documentsClient spec sheet v2, approved golden sample, packing list

2. Sampling plan

StandardLevelLot sizeCodeSample sizeCriticalMajor AQL 2.5Minor AQL 4.0
ISO 2859-1, single sampling, normalGeneral II3,000K125Ac 0 / Re 1Ac 7 / Re 8Ac 10 / Re 11

Cartons for sampling were selected at random by the inspector from all stacks. Function tests used a sub-sample agreed with the client (13 pcs, 5 pcs for destructive tests).

3. Results by section

SectionResultNotes
Quantity and packing listPASS120 cartons counted, matches packing list.
Packing, carton marks, barcodesPASS10 of 10 barcodes scanned and readable. Carton marks match spec.
Workmanship (visual), 125 pcsFAIL8 major and 6 minor visual defects. See section 4.
Function tests, 13 pcsFAIL1 vacuum failure (major). See section 5.
Coating adhesion, 5 pcsFAIL1 of 5 at 3B, requirement ≥4B.
Capacity, size and weight, 5 pcsPASSAll within spec tolerance.
Food-contact documentsINFOFactory showed a third-party test report for the steel and lid materials. Sighted only, not verified with the lab.

4. Defects found

#DefectClassQtyPhoto
1Coating chip at base edge, 1 mm or larger, steel visibleMajor5P1–P3
2Lid gasket not fully seated in its grooveMajor2P4
3Dent on body, 2 mm or largerMajor1P5
4Lost vacuum: outer wall warm after hot fill (from function tests)Major1P6
5Light surface scratch on body, under 10 mmMinor3P7
6Logo print off-centre by 1–2 mmMinor2P8
7Dust inside gift boxMinor1—
ClassFoundAccept / RejectResult
Critical (unsafe, e.g. sharp edge)00 / 1PASS
Major97 / 8FAIL
Minor610 / 11PASS

5. Function and on-site tests

TestMethodRequirementQtyResult
Heat retentionPre-heat, fill with 95 °C water, close lid, room at 23 °C, read at 6 h≥ 60 °C at 6 h (client spec)1313/13 64–69 °C
Vacuum checkFill with 95 °C water, wait 10 min, IR thermometer on outer wallOuter wall ≤ room temp + 3 °C1312/13 Unit #88 at 41 °C
Leak testFill to the brim, close lid, hold upside down on paper for 30 minNo leak, no damp paper1313/13
Coating adhesionCross-hatch tape test, ASTM D3359 Method B, at base edge≥ 4B54/5 One at 3B
CapacityFill to brim, weigh the water500 ml, −0 / +5%55/5 512–518 ml
Lid fitOpen and close 10 times, check thread and gasketSmooth, no cross-threading1313/13
OdourHot rinse, close for 10 min, smellNo abnormal odour1313/13
Carton dropISTA 1A drop sequence from 76 cm, 10 dropsNo product damage1 ctnPASS

6. Recommendation

  1. Do not ship this lot as is.
  2. Factory to sort 100% for base-edge coating chips and re-seat any loose gaskets. Units that fail the vacuum check must be removed.
  3. Re-inspect the sorted lot before release.
  4. Chips and the low adhesion result are both at the base edge, which points to coating adhesion rather than handling damage. Ask the factory to check surface pre-treatment and curing for the base edge before the next lot.

7. Factory record

LotDateSampleMajor defectsMajor rateMain issueResult
Lot 1 (this report)Sample12597.2%Base-edge coating chipsFAIL
Lot 2————Added after the next inspection—

Each factory keeps one running record, so you can see whether the same problem comes back and whether fixes hold.

8. Photo evidence

P1 · Base-edge chip, 1.5 mm, unit #47
P2 · Base-edge chip, unit #63
P3 · Chip close-up with ruler
P4 · Gasket out of groove
P5 · Body dent, 2.5 mm
P6 · IR reading 41 °C, unit #88
P7 · Surface scratch
P8 · Logo offset vs golden sample

Photos are omitted in this sample. Real reports include a photo or short video for every defect and every test.

Results apply only to the samples inspected on the date stated and do not release the factory from its obligations to the client. Firsthand QC is an independent inspection service, paid only by the client. · firsthandqc.com · [email protected] · Hangzhou, Zhejiang, China